Leaky faucets, dripping pipes and faulty valves can be a real pain for any homeowner. According to a survey, water leaks cause houses to lose 14% of their water. Even more alarming is the fact that water causes losses of almost $9 billion between 2007 and 2009.

Many of us spend hundreds of our hard-earned dollars and hours upon hours of our precious time in the kitchens or the showers trying to fix the problems. The problem gets even more out of hand when we realize that the engineering is incomprehensible and that a plumber must be brought in. The end result is a wastage of time and money to sort out problems that weren’t even as complex in the first place. The truth is that many of these problems can be easily fixed. All you need is a bit of determination, some tape and a few other necessities from myhousesupplies.com.

How myhousesupplies.com Can be of Help

Here are 5 DIY plumbing fixes that will help you save cash. Most of the things you need to implement these DIY fixes are available at myhousesupplies.com.

Preventing/Fixing Leaks in Joints

A lot of the plumbing joints are simply protected/enabled by threaded pipe. This is often not sufficient enough to prevent future leaks. The first step to dealing with a leaky joint is by starting with strengthening these joints. It is recommended that you get hold of a high-quality tape or even strong glue and apply it to the pipe therefore making any future leaks virtually impossible. For pipes with compression joints, we have another simple method. Usually, compression joints come with a ring which fits into the compression thus preventing leaks. All you have to do is lubricate the pipe and the ring using some relevant compound. This allows the ring to fit perfectly into the compression. Next, just tighten the ring around the pipe using a wrench or any suitable tool.

Leaky Faucets

This is one of the more common problems in the house and often one of the more annoying ones as well. Truth be told, it is quite easy to fix. Ceramic disc faucets are more commonly used. To fix them, first turn off water supply and get hold of an empty container where you can leave all the smaller parts thus preventing them from being lost. Then, remove the handle. You will probably need a small knife to remove the screw. Upon removing the handle, you will notice a cartridge. Remove this too. Next, take a close look at the cartridge as it requires cleaning. Once this is done, you must replace the rubber seals. In some cases, there may be O-rings which you might need to replace.

Faulty Toilet Tank

Another fairly common problem, this is also quite easy to fix. All you need is some pliers and some gloves (to maintain hygiene). Let’s say your toilet isn’t flushing properly and there is little water each time. To fix this, you need to open the tank lid and find a flexible pipe running between the two vertical pipes called fill valve and overflow tube. If the flexible pipe (known as fill tube) misses the other tube and is displaced, you will face the problem mentioned above. Just position it according to its standard position and ensure that the overflow tube is 1 inch below the tube.
Sometimes, there is also an issue with the float that controls the level of water in the tank. Low water level would mean an unimpressive flush while a high water level would mean that the toilet would keep running. The simplest way to deal with this is by opening the lid and taking note of the prescribed water level mark. Mark this level on the overflow tube and then flush the tank adjusting the float until the water settles at the identified mark.

Unclogging the Bathtub Drain

It is always bad to discover that you are standing in a puddle of water while taking a shower. A closer look tells you that all of your soap water has simply been collecting at your feet rather than draining away. However, cleaning the drain really is quite simple. If you have a drop stopper type of drain, then you can remove the head by removing the screw and getting the stopper off. Then, grab a used hanger or a stiff straightened wire and slide it into the drain to catch the clogged mess which is usually a ball of hair. In case you have a ‘push-press’ drain stopper, it can be slightly trickier. Just hold on to the shaft and attempt to unscrew the top to get to the drain underneath.

Unclogging a Toilet

For most cases, you will just need a plunger and some motivation. Wear gloves because things mostly certainly can get a little messy. Plungers are powerful manual machines that can get rid of most clogs. Just make sure to blow out the air on your first plunge by applying gentler force. After this, you can slowly increase power gently with each plunge but the key here is to remain steady in force. While plunging, ensure that the plunger is covered with water.


If a plunger doesn’t work, things might be a little more serious than we imagined. Of course, there are some other tools to help unclog trickier messes. One example would be a plumbing wire which is a flexible machine used to unclog the most obstinate obstacles.

One of the most important factors in preventing plumbing problems is the kind of material used. Pex tubing is a revolutionary material that is used in plumbing. Pex tubing is not only stronger and more long-lasting, but is also much more environment friendly. The pex tubing come with a coat of EVOH polymer that prevents rust and decomposition. The material is so strong that you will probably need a special pex cutter to cut through the pipe if you ever need to.

They say that the key to keeping a house well-maintained is by preventing all malfunctions. This simple DIYs will certainly help you save time and cost and would also help you attain peace of mind.